Contents. (Click on a component to see usage instructions.)
Enamel Etching Gel (37% Phosphoric acid)
Enamel Etching Gel (37% Phosphoric acid) Usage.
Apply to tooth for 15 seconds and copiously rinse the tooth. Tooth should exhibit a “frosty, white appearance” If not, re-apply for further 10 seconds and rinse.
Acid etches tooth surface to enhance bond.
Click here to order this component
Close
Silane Bond Enhancer 3ml
Silane Bond Enhancer 3ml Usage.
Apply to veneer, gently blow off excess and let dry.
Increases bond strength of restoration by 15%.
Click here to order this component
Close
Adhesive Resin activator (Dentine Bond) A. 6ml
Adhesive Resin activator (Dentine Bond) A. 6ml Usage.
Mix A + B in disposable mixing pot (supplied in kit) and wait 1 minute. Apply to lightly air dried surface of tooth and wait 10 seconds. If surface is not shiny, apply further coats until shiny appearance is present. Very lightly blow off excess, do not let it puddle. Can take one to six coats dependant on tooth age.
Enhances bonding and seals dentine tubules.
In short, stops any post – operative sensitivity. Sometimes called “Dentine adhesive” Recommended even when you believe no dentine has been exposed.
Click here to order this component
Close
Adhesive Resin activator (Dentine Bond) B 6ml
Adhesive Resin activator (Dentine Bond) B 6ml Usage.
Mix A + B in disposable mixing pot (supplied in kit) and wait 1 minute. Apply to lightly air dried surface of tooth and wait 10 seconds. If surface is not shiny, apply further coats until shiny appearance is present. Very lightly blow off excess, do not let it puddle. Can take one to six coats dependant on tooth age.
Enhances bonding and seals dentine tubules.
In short, stops any post – operative sensitivity. Sometimes called “Dentine adhesive” Recommended even when you believe no dentine has been exposed.
Click here to order this component
Close
Unfilled Resin base 3ml Tube
Unfilled Resin base 3ml Tube Usage.
Thins down the applied composite for difficult to fit veneers etc and allows for a sliding movement on fitting.
Apply to veneer and / or tooth. Do not over apply as this weakens the filler content of the composite.
Click here to order this component
Close
Light Cure Composites 4gm Tubes
Light Cure Composites 4gm Tubes Usage.
For light cure fitting of thin Restorations.
Choose composite colour of choice and apply lightly to Veneer or Restoration and slide into place. Whilst holding restoration in place, gently brush off excess with bendy brushes supplied in kit. , Brush at right angle to margin so as not to remove composite from fit edge. Cure with light for 15 –30 seconds to fix restoration in place and then re-clean.
Light cure for a further 2 minutes or longer. (It is difficult to over cure.)
Click here to order this component
Close
Duo Cure Universal shade
Duo Cure Universal shade Usage.
For use with inlays, thick Veneers or full Restorations etc where light alone may not fully cure the composite.
Mix with Composite colour of choice 50/50, apply to restoration and treat as above for light cure composite fitting.**
Use Low fill chemical catalyst paste for veneers.
Use Heavy fill chemical catalyst paste for inlays etc where high filler content of composite is required to prevent wash out of cement media by saliva over time.
** Use of a light can kick start the curing process and allow for clean up of hard to get to places early in the curing process.
If in any doubt of your curing lights capacity, or the depth of restoration, we recommend you use chemical cure.
Click here to order this component
Close
Chameleon Diamond Paste.2.5gm Tube
Chameleon Diamond Paste.2.5gm Tube Usage.
For cleaning and polishing of edges of Veneers, Restorations etc after trimming of excess composite with different degrees of diamond burs from course to smooth.
Apply with soft rotary brush and slow speed. Imparts a high gloss appearance to both edge of Restoration and also Restoration itself.
Also ideal for re-polishing all Ceramic and Gold Restorations after easing Occlusion or margins.
One small tube seems to last forever.
Click here to order this component
Close
